Thumbnail Image

Kerala Agricultural University, Thrissur

The history of agricultural education in Kerala can be traced back to the year 1896 when a scheme was evolved in the erstwhile Travancore State to train a few young men in scientific agriculture at the Demonstration Farm, Karamana, Thiruvananthapuram, presently, the Cropping Systems Research Centre under Kerala Agricultural University. Agriculture was introduced as an optional subject in the middle school classes in the State in 1922 when an Agricultural Middle School was started at Aluva, Ernakulam District. The popularity and usefulness of this school led to the starting of similar institutions at Kottarakkara and Konni in 1928 and 1931 respectively. Agriculture was later introduced as an optional subject for Intermediate Course in 1953. In 1955, the erstwhile Government of Travancore-Cochin started the Agricultural College and Research Institute at Vellayani, Thiruvananthapuram and the College of Veterinary and Animal Sciences at Mannuthy, Thrissur for imparting higher education in agricultural and veterinary sciences, respectively. These institutions were brought under the direct administrative control of the Department of Agriculture and the Department of Animal Husbandry, respectively. With the formation of Kerala State in 1956, these two colleges were affiliated to the University of Kerala. The post-graduate programmes leading to M.Sc. (Ag), M.V.Sc. and Ph.D. degrees were started in 1961, 1962 and 1965 respectively. On the recommendation of the Second National Education Commission (1964-66) headed by Dr. D.S. Kothari, the then Chairman of the University Grants Commission, one Agricultural University in each State was established. The State Agricultural Universities (SAUs) were established in India as an integral part of the National Agricultural Research System to give the much needed impetus to Agriculture Education and Research in the Country. As a result the Kerala Agricultural University (KAU) was established on 24th February 1971 by virtue of the Act 33 of 1971 and started functioning on 1st February 1972. The Kerala Agricultural University is the 15th in the series of the SAUs. In accordance with the provisions of KAU Act of 1971, the Agricultural College and Research Institute at Vellayani, and the College of Veterinary and Animal Sciences, Mannuthy, were brought under the Kerala Agricultural University. In addition, twenty one agricultural and animal husbandry research stations were also transferred to the KAU for taking up research and extension programmes on various crops, animals, birds, etc. During 2011, Kerala Agricultural University was trifurcated into Kerala Veterinary and Animal Sciences University (KVASU), Kerala University of Fisheries and Ocean Studies (KUFOS) and Kerala Agricultural University (KAU). Now the University has seven colleges (four Agriculture, one Agricultural Engineering, one Forestry, one Co-operation Banking & Management), six RARSs, seven KVKs, 15 Research Stations and 16 Research and Extension Units under the faculties of Agriculture, Agricultural Engineering and Forestry. In addition, one Academy on Climate Change Adaptation and one Institute of Agricultural Technology offering M.Sc. (Integrated) Climate Change Adaptation and Diploma in Agricultural Sciences respectively are also functioning in Kerala Agricultural University.

Browse

1990 - 19966
Reset filters
Subject: Agricultural Engineering × End date: 1999 × Start date: 1990 × Type: Thesis × Thesis Type: M.Sc ×
Reset filters

Search Results

Now showing 1 - 6 of 6
  • Thumbnail Image
    ThesisItemOpen Access
    Optimum thresher parameters for high moist paddy
    (Department of Farm Power Machinery and Energy, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1993) Hamza, Mollakadavath; KAU; Sivaswami, M
    The study undertaken by the newly development 1 hp paddy thresher to optimise its parameters for high moist paddy revealed that the peripheral velocity from 10.80 to 21.72 m/s on the rasp – bar, spike tooth, double directional spiral cylinders didn’t influence much on the threshing efficiency. When the moisture content was increased to 35 per cent, the threshing efficiency was brought down from 98.4 to 92 per cent for rasp – bar cylinder and was increased from 88 per cent to 94 per cent in the case of double directional spiral cylinder. The maximum threshing efficiency of 99 percent was achieved for spike tooth cylinder at 19.2 per cent moisture level. The maximum threshing efficiency of 94% and the maximum output of 340 kg/h were achieved with the double directional spiral cylinder when the moisture content was 35% per cent. The proto – type thresher was found to reduce the cost of threshing to 81 per cent and reduction in labour to 85.16 per cent compared to the manual threshing.
  • Thumbnail Image
    ThesisItemOpen Access
    Design development and evaluation of a low cost paddy thresher
    (Department of Farm Power Machinery and Energy, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1991) Mathew, John; KAU; Sankaranarayanan, M R
    Though several high capacity threshers are available in the country for different crops, no thresher is found suitable for small and marginal rice farmers. Hence a low cost portable paddy thresher was developed and tested. The power operated machine consists of base, side frames, front grain shield and wire-loop cylinder. The power from the 0.5 hp motor is transmitted to the cylinder shaft by belt and pully arrangement. The optimum cylinder speed is 400 rpm. The capacity of the thresher at 14.26 per cent moisture content is 451.84 kg paddy per hour and threshing efficiency is 95.08 per cent. The mechanical damage of the grain is negligible. Two labourers are required for the whole operation. The size of the thresher is 635 x 500 x 715 mm having a gross weight of 47 kg. The cost of the thresher was worked out to be around Rs. 3600 and the cost of operation for threshing paddy was Rs. 3.00 per quintal. The unit can be fabricated by local artisans from the readily available materials and can successfully be maintained by small and marginal farmers.
  • Thumbnail Image
    ThesisItemOpen Access
    Development and performance evaluation of a rotary tillage attachment to the KAU garden tractor
    (Department of Farm Power Machinery and Energy, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1990) Jose, C M; KAU; Sivaswami, M
    Considering the advantages of rotary tillers over non-powered tillage tools, and in order to make the KAU garden tractor a versatile farm power unit, a rotary tillage attachment for the garden tractor was developed and tested. The main components of the rotary tillage attachment are mainframe, power transmission system, blade assembly, hitching mechanism and protective cover. The depth of tillage obtained is 10 to 15 cm and the effective width of field coverage is 30 to 32 cm. The actual field capacity of the machine is 0.054 ha per hr and the quantity of fuel required to operate the machine is 0.860 1 per hr. Operator can easily walk behind the rotary tiller and turn the garden tractor to either side. The cost of production of the rotary tillage attachment is Rs. 1500.00 and the total cost of ploughing per hectare using the machine is Rs. 450.00.
  • Thumbnail Image
    ThesisItemOpen Access
    Development and performance evaluation of a low cost water-wheel for lifting water at low heads
    (Department of Farm Power Machinery and Energy, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1992) Jayan, P R; KAU; Sankaranarayanan, M R
    A low cost water wheel was designed, fabricated and tested in the distributory canal of KCAET farm, Tavanur. The device was operated by the stream current with no additional power source and was tested for different submergence depths varying from 0.12 to 0.25 m. Water wheel with eight cups of 30 cm x 7 cm x 2 cm intake compartment was found to be the most efficient under various operating conditions. A maximum efficiency of 48% was obtained at 0.23 m of submergence depth. The device can lift water without additional operating cost as long at the mean stream velocity is greater than or equal to 0.44 m/sec for the optimum depth of submergence at 23 cm. The corresponding discharge of the system is 19.2 lpm at 0.6 m head. The investment cost of the device is Rs. 800/- and the annual operating cost is Rs. 204/- with low maintenance cost. Though the power output and the discharge capacity were low, it has a two fold advantage of functional reliability and simplicity of design and fabrication at village level. It can successfully be utilised by the small farmers when the cultivating fields are adjuscent to the canal water courses.
  • Thumbnail Image
    ThesisItemOpen Access
    Dynamics of power transmission in tractor mounted paddy reaper
    (Department of Farm Power Machinery and Energy, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1996) Sushilendra; KAU; Sivaswami, M
    A tractor front mounted 2.2 m wide paddy reaper windrower was evaluated to find out the optimum forward speed, cutterbar speed, conveyor belt speed and engine speed for different field conditions to achieve better harvesting and windrowing pattern, Maximum field capacity and field efficiency with less harvesting losses. Three PTO pulleys of 17.78 cm, 19.03 cm and 20.32 cm diameter with internal splines were fabricated and used with an engine speed from 1000 to 2000 rpm with four gears in low range and first gear in high range. In addition to pneumatic tyres, a pair of special cage wheels and a simple collection unit were developed and evaluated. In water submerged fields with special cage wheels and PTO pulley of 17.78 cm diameter better results were observed when reaper was operated at an engine speed of 1500 rpm with third low gear with a forward speed of 0.95 m/s. The optimum cutterbar index and conveyor index were found to be 1.56 and 2.30 respectively. The actual field capacity was 0.38 ha/hr and field efficiency was 54 per cent. The crops were found to throw within 10 cm from the discharge plate with an tiller angle of more than 85 degree with only 1.54 per cent of total loss of grain. When the soil is moist and pneumatic wheels fail to give sufficient traction, the special cage wheels were used with a PTO pulley of 19.03 cm diameter. An engine speed of 1400 rpm with third gear and with a forward speed 0.90 m/s was found to give satisfactory performance. The optimum cutterbar index was 1.66 and conveyor index was 2.45. The reaper had the field capacity of 0.36 ha/hr with field efficiency of 53 per cent. The windrowed crop were found to throw within a distance of 13.5 cm with 85 degree of tillers angle with total grin loss of 1.55 per cent. For dry fields, the reaper with pneumatic wheels was found to operate satisfactorily with 20.32 cm diameter PTO pulley at an engine speed of 1300 rpm with fourth gear and with a forward speed of 1.00 m/s. The optimum cutterbar index was 1.48 and conveyor index was 2.19. The actual field capacity was 0.38 ha/hr and field efficiency was 50.66 per cent. The tillers angle was 85 degrees with total grain loss of 1.62 per cent. It is found that the better field performance was achieved when the reaper is operated at a cutterbar speed of 1.50 m/s and conveyor belt speed of 2.20 m/s. A simple crop collection unit of size 1. 5m x 0.7m x 0.35m was developed with the provision for conveying the windrowed crop directly into the collection box. The unit was field evaluated with reaper. The box was found to fill within 10 m of travel and problems were observed in its manoeuv reability, loading and unloading of box and increased idle time.
  • Thumbnail Image
    ThesisItemOpen Access
    Design fabrication and testing of a low cost greenhouse
    (Department of Irrigation and Drainage Engineering, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1995) Ajayambikadevi, S J; KAU; Remadevi, A N
    Controlled environment agriculture in the form of greenhouses, low tunnels and cloches are being practiced at commercial levels in many countries. Among these the greenhouses are the best for active environmental control. The major hurdle for adopting greenhouse cultivation is its high initial investment. Considering the importance of developing greenhouses of simple design with low initial investment, the thesis entitled ‘Design, Fabrication and Testing of a Low Cost Greehouse’ was undertaken. A greenhouse of size 12 m x 3 m was constructed at the Instructional Farm, KCAET, Tavanur. The structure was gable shaped. The main structural members were hoops, ridge line mechanism, foundation material and the structure for pad gripping and fan replacement. Ultraviolet stabilized polyethylene film was used as the glazing material. The fan and pad system of cooling in which the air is cooled by the moist air drawn through the wetted pads was adopted. The system was designed based on the rate of air to be removed from the greenhouse. A fan of maximum air flow rate of 10450 m3 /hr and a pad of size 3000 mm x 1200 mm was found necessary to satisfy the cooling requirements. The climatological parameters namely dry bulb temperature, wet bulb temperature and intensity of solar radiation were measured both inside and outside the greenhouse. The cooling system was operated for various time intervals and the observations were taken under cooled and uncooled conditions of the greenhouse. The temperature inside the greenhouse was higher than that outside. The maximum temperature recorded inside the greenhouse was 47.60C without cooling and 38.50C with cooling. Longitudinal temperature gradient of 50C existed between the fan end and pad end of the greenhouse. Cooling increased the relative humidity inside the greenhouse. Variation in humidity existed between the pad end and the fan end. A desired temperature and relative humidity can be maintained inside a greenhouse by operating the cooling system for various time intervals. The variation of solar intensity inside the greenhouse was similar to that outside. The polyethylene cover transmitted 60 per cent of the solar radiation incident on it. The average efficiency of the pad was 65 per cent. The cost of construction was Rs. 375.58 per square metre.