Thumbnail Image

Theses

Browse

19953
Reset filters
End date: 1995 × Start date: 1995 × Thesis Type: M.Tech. ×
Reset filters

Search Results

Now showing 1 - 3 of 3
  • Thumbnail Image
    ThesisItemOpen Access
    Evaluation and modification of powertiller operated paddy reaper
    (Department of Farm Power Machinery and Energy, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1995) Selvan, P; KAU; Sivaswami, N
    The study on power tiller operated paddy reaper-windrower was taken up solve the problems of labour scarcity and uneconomic cost of cultivation of paddy. The 1.6 m vertical conveyer reaper-windrower was fabricated and was mounted with commercially available 8-10 hp air cooled Mistubishi power tiller. Improvements and modifications were carried out to make the unit suitable for harvesting of paddy in Kerala. The original engine chasis of the power tiller was replaced with a newly fabricated chasis on which both the engine and paddy harvester were mounted. Difficulties were experienced in starting and in operating the harvester when the drive was taken directly from the engine pulley to the cutterbar. Initialy the unit was operated with rotovator at the rear side. It was found difficulty in crossing the bunds, hence rotovator was removed. After detailed studies, an auxiliary gear box was designed and fabricated for transmitting power to reaper from the rotovator gear assembly. The rear rotovator was dismantled and the auxiliary gear box was assembled. For balancing, a counter weight of 35 kg was added in between the handles. The crop is cut by the reciprocating knife while passing through crop dividers, star wheels, pressure springs and is conveyed by a pair of lugged conveyer belts and is discharged as a neat windrow. Improvements and modifications were carriedout on most of the reaper components. Field evaluation of paddy harvester was carried out at KCAET Tavanur for two seasons. It was found that harvester has an effective cutting width of 1.55 m and an average field capacity of 0.02036 ha/hr. The pre harvest loss, sickle loss, shattering loss and total cutter bar loss were found to be 0.005 per cent, 2.43 per cent and 0.026 per cent respectively. The power tiller operated reaper-windower was found suitable for harvesting paddy both in wet as well as dry fields except the fully lodged crops. It is an appropriate machinery for harvesting paddy and is found economically and technically suitable for Kerala conditions. It was calculated that manual harvesting needs Rs. 1625/ha whereas power tiller operated reaper needs only Rs. 348/ha and thus achieved a saving of amount of Rs. 1277/ha. The savings of 186 man-hrs/ha achieved by the introduction of power tiller operated paddy reaper is a promising solution for the crisis of labour scarcity and the high cost of labour input in the paddy cultivation.
  • Thumbnail Image
    ThesisItemOpen Access
    Simulation studies on different design parameters of spurs (Groynes)
    (Department of Land and Water Resources and Conservation Engineering, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1995) Roy, Mathew; KAU; Xavior Jacob, K
    The Use of spurs as river training measure has proved to be an effective means of protecting river bank and their design requires indepth knowledge about its parameters related to the solution of a specific river training problem. To analyse various design parameters of spurs, a simulation study was conducted at KERI,Peechi. Characteristics such as flow pattern, velocity distribution and scour pattern was analysed for different spur lengths 25 cm, 35 cm, 45 cm and 55 cm, spur angles 900, 1000, 1100 and 1200, spur spacings 2L, 3L, 4L and 5L and for discharge rates 14.14 1ps, 28.28 1 ps and 42.42 1 ps. Single spur and multiple spur scheme were tested on rigid as well as mobile bed condition. The analysis of the obtained flow pattern, velocity distribution and scour pattern reveals that the specified design parameters have a significant effect on flow diversion, length of bank protected, maximum scour depth at the spur nose, percentage increase in velocity at opposite bank etc. The analysis of the present study also led to conclusion that L/B ratio of 0.19, spure angle of 900 was the best combination for single spur study and the same with a spacing of 5L was most effective for multiple spur scheme.
  • Thumbnail Image
    ThesisItemOpen Access
    Development and testing of a rotary type black pepper cleaner
    (Department of Farm Power Machinery and Energy, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1995) Abdul Wahab, V S; KAU; Jippu, Jacob
    A power operated rotary type black pepper cleaner is developed, tested and its performance evaluated. The major parts are an inclined circular disc, an involute shaped scraper, a feeding unit and a collecting tray. The black pepper admixture is fed to the drum sieve through a hopper. By rotating the sieve, feed material fall uniformly over one-half of the area of the inclined rotating disc. Good pepper grains being nearly spherical in shape roll down at one end, whereas foreign materials which cannot roll down as freely, is scraped out at the other end by means of an involute scraper. Both cleaned and uncleaned grains are received in a collecting tray placed below the disc. A 3-phase 0.5 HP variable speed dynodrive motor along with a 10:1 gear reduction unit operates the machine. The important physical properties of black pepper relevant to cleaning process are also studied. The trials are repeated for the surfaces of mica and cotton under different levels of feed rate, angle of inclination and speed. Better performance is obtained in the case of cotton surface. Under these conditions, a cleaning efficiency of 88 per cent is obtained at a feed rate of 12 kg/h, angle of disc 11o and at a speed of 10 rpm. The cost of the machine excluding the power unit comes to Rs. 1’100/-. The operating cost of machine is found to be Rs. 16.45/h. It is recommended for further studies and modifications.