Thumbnail Image

Theses

Browse

Reset filters
Subject: Agricultural Engineering × Author: KAU × End date: 2014 × Thesis Type: M.Tech. ×
Reset filters

Search Results

Now showing 1 - 9 of 31
  • Thumbnail Image
    ThesisItemOpen Access
    Performance and ergonomic evaluation of direct pady seeder and mechanical rice transplanter in wet lands
    (Department of Farm Power Machinery and Energy, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 2013) Rathod Sachin, Ravsu; KAU; Sureshkumar, P K
    An experiment was conducted to evaluate the performance of the ‘Aiswarya’ 8 row direct seeder and ‘Mahindra PF455S’ 4 row walk behind mechanical transplanter with ‘Jyothi’ rice variety in wet lands from the ergonomic point of view. It conducted with selected male and female subjects in the age group of 25–35 years. The performance of these machines was compared with manual transplanting. The results show that the seed rate for direct seeder was very low with 37 kg ha-1 as compared to the mechanical transplanter (55 kg ha-1) and manual transplanting (72 kg ha-1). EFC found for direct seeder and mechanical transplanter was 0.11 ha h-1and 0.12 ha h-1 respectively. The field efficiency was found to be 69% for direct seeder and 74% for mechanical transplanter. Fuel consumption of the mechanical transplanter was found 3.7 l ha-1. The grain yield and straw yield in mechanical transplanting method was higher 2652 kg ha-1 and 3482 kg ha-1 as compared to 2265 kg ha-1 and 2885 kg ha-1 in the case of direct seeding. But in the case of manual transplanting, the yields were 2025 kg ha-1 and 2508 kg ha-1 respectively. The mean value of WHR and OCR with direct seeder was 145.5 beats min-1 and 0.95 l min-1 for male and 148.9 beats min-1 and 0.98 l min-1 for female. But in case of mechanical transplanter, the mean value of WHR and OCR was 131.6 beats min-1 and 0.80 l min-1 for male and 134.1 beats min-1 and 0.83 l min-1 for female. There was complete recovery of HR after 8 min with direct seeder and 6 min with mechanical transplanter. In case of direct seeder ODR, OSR, OER, BPDS values were given by male 6.5, 0, 6.0, 40.8 and by female 7.5, 0, 7.5, 45.6. The corresponding values for mechanical transplanter were 3.0, 1.5, 3.5, 36 by male and 3.5, 1.5, 5.0, 36. As per the grading of energy cost of work, direct seeder categorized as “very heavy type” and mechanical transplanter as “heavy type”. The 8 row direct seeder is not suitable for female subjects. A 4 row Mahindra walk behind mechanical transplanter could be used successfully not only to improve the yield but also to provide operator comfort as compared to the 8 row direct seeder.
  • Thumbnail Image
    ThesisItemOpen Access
    Development and evaluation of modified atmosphere packed passion fruit(Passiflora edulis)
    (Department of Post harvest technology and agricultural processingKelappaji College of Agricultural Engineering and Technology, Tavanur, 2012) Madhana Supriya, R; KAU; Sudheer, K P
    Passion fruit is a tropical fruit which is extensively used in juice processing. The fruit is highly perishable and losses its quality immediately after the second day of harvest. The postharvest loss in quality and commercial value is due to the intense respiratory activity and significant moisture loss. Hence a study was undertaken to develop a wax applicator to extend the shelf life of passion fruit by adopting the postharvest technologies. A simple and efficient wax applicator with a capacity of 250 kg.hr-1 was developed based on the physical properties of the fruits. Various samples of the passion fruits were treated with bee wax and commercial wax packed in LDPE bags of 200 and 400 gauge. The effect on the shelf life extension of fruits was investigated individually and in combination of wax and LDPE bags. In the case of LDPE bags, different levels of perforations such as 0%, 0.5%, 1% and 2% were used. The samples were kept in ambient condition viz., 32 - 35°C and 70 - 80% RH and at cold conditions as 7ºC and 90% RH. The physicochemical characteristics of samples were tested periodically at an interval of 5 and 7 days, under ambient and cold storage conditions, respectively. The results obtained were subjected to statistical analysis. From the results it was revealed that the samples kept in non-perforated polythene covers were found to be better than those kept in perforated bags and in normal atmosphere. A maximum shelf life of 40 days was obtained for passion fruits at 7oC coated with commercial wax emulsion. Thus, commercial wax coating in combination with LDPE bags acted as a barrier against moisture loss and respiration rate of fruits. However, the fruits kept as control had lost consumer acceptability after the tenth day of study at cold condition and within two days at ambient storage conditions.
  • Thumbnail Image
    ThesisItemOpen Access
    Water balance study of Karuvannur river basin
    (Department of Irrigation and Drainage Engineering, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1988) Santosh, G Thampi; KAU; John Thomas, K
    This study was undertaken to quantitavely assess the water resources of the Karuvannur River Basin and to study the monthly water balance in order to estimate the balance for ground waterrecharge or depletion during the period 1976 to 1985. The mean monthly rainfall over the basin during the period 1976-1985 was determined by Thiessen polygon method . Data regarding the amount of water released for irrigation from the Peechi reservoir was also collected. Due to lack of data, contribution from other sources was not taken into account. The total runoff from the basin during each month of this period was determined . The various crop combinations in the basin were identified and the area under each of these was estimated . The actual evapotranspiration during each month was estimated using the method outlined by Doorenbos and Kassam. The basin was regarded as an independent hydrologic unit . Hence surface and subsurface inflow and outflow were assumed to be negligible.
  • Thumbnail Image
    ThesisItemOpen Access
    Development of a low cost garden tractor
    (Department of Agricultural Engineering, College of Horticulture, Vellanikkara, 1982) Sivaswami, M; KAU; Muhammad, C P
    The study was conducted with the objectives of systematic analysis of components with respect to their kinematics, dynamics and ergonomics and evaluation of traction performance and economics of low cost garden tractor. A greaves Lombardini 5.4 hp diesel engine with 1800 rpm was selected and a simple three step speed reduction system having a single stage V belt drive and double stage chain drives with a pivotted countershaft clutch have been designed. A road speed of 6.635 kmph and field speed of 3.317 kpmh were achieved by using a cone pulley arrangement with 6.00 x 12 size wheel.Correct position of various components bringe the centre of gravity of the unit with and without implement at very close to the final drive axle for easy balancing
  • Thumbnail Image
    ThesisItemOpen Access
    Development of small scale equipment for extraction of cocoa butter and production of cocoa powder
    (Department of Agricultural Engineering, College of Horticulture, Vellanikkara, 1982) Ganeshan, V; KAU; George, T P
    The primary objective of this project was to evolve a viable technology and equipment system for small scale processing of cocoa beans. The study mainly concentrated on the development of an extraction unit for the separation of butter from cocoa mass. Various equipment required for small scale processing of cocoa beans were either identified or designed.
  • Thumbnail Image
    ThesisItemOpen Access
    Development and field evaluation of a cardomom polishing machine
    (Department of Farm Power Machinery and Energy, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1999) Anu, Ray Mathew; KAU; Mohammad, C P
    Cardamom capsules when dried have a dried flower stalk which is hard to be removed by manual operation. For destalkinq, a power operated cardamom polishing machine was developed, tested and its performance was evaluated. A polishing drum with attached wooden blades seperated the dried capsules fed in. from the flower stalk attached and were collected seperately. A single phase 1 hp motor served as power source. A 3-factlJr, factorial experiment in Completely Randomized Design (CRD) with drum speed, feed/batch, and retention time as independent variables was performed.
  • Thumbnail Image
    ThesisItemOpen Access
    Design, fabrication and testing of a power operated paddy dibbler
    (Department of Farm Power Machinery and Energy, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1996) Jayarajan, R; KAU; Jippu, Jacob
    A 2-row power operated paddy dibbler was designed, fabricated and tested at Kelapaji College of Agricultural Engineering and Technology, Thavanur. The main components of the dibbler were two seed boxes, plungers reciprocating within the seed tubes, fluted roller seed metering mechanism, dibbler wheels, stationary cam, frame and transport wheels. The seed tubes were fixed radially around the dibbler wheel with 45 mm of it projecting outwards for penetrating the soil. The plunger was actuated by a stationary cam and during its upward stroke it uncovered the farther end of the seed transfer tube and transferred the seeds into the seed tube and then into the holes made in the soil. In the downward stroke the plunger closed the seed transfer tube. Simultaneously the fluted roller transferred the seeds in to the seed transfer tube. The average speed of operation of the dibbler was 1.32 kmph and its field capacity and field efficiency were 0.031 ha/h and 78.18 per cent respectively. The average number of seeds dropped per hill was 5 and the seed rate obtained was 78 kg/ha. The seeds were placed within the confines of the holes made by the seed tube and plunger. There was absolutely no scattering. The depth of placement varied from 3.8 to 4.6 cm. The operating cost of the dibbler was Rs. 502.58/ha. This mechanism offers scope for developing dibblers with more number of rows for being operated more economically.
  • Thumbnail Image
    ThesisItemOpen Access
    Modification and performance evaluation of six row rice transplanter for conventional seedlings
    (Department of Farm Power Machinery and Energy, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1990) Bainu, T Kuzhively; KAU; Sivaswami, M
    The work was carried out at the Kelappaji College of Agricultural Engineering and Technology, Tavanur. The six – row rice transplanter was originally designed for mat type seedlings. Considering the importance of a transplanter using conventional type seedlings, the above transplanter was modified. The modifications were completed in three stages. The performance evaluation of the modified six row rice transplanter was conducted after each stage of modification. The average number of seedlings per hill could be reduced from the average value of six seedlings per hill before modification to 2.27 seedlings per hill after the modifications. The missing hills percentage was brought down from 20.83 per cent to 5.55 per cent and the floating hills percentage was reduced from 10 to 5.55. Percentage of damaged hills was reduced from 23.3 to 8.8. The field capacity of the machine was improved from 0.0139 ha/hr to 0.0162 ha/hr and field efficiency from 48.26 percent to 56.87 per cent. The use of the modified transplanter is profitable if it is operated beyond one hectare per annum. It gives a saving of Rs. 618.00 per hectare compared to the conventional hand transplanting giving a 2. 4 times reduction in total cost. The pay back period of the modified transplanter is 2.24 years when the annual utilization is 2 hectares per annum and 1.13 years when the annual utilization is 3 hectares per annum.
  • Thumbnail Image
    ThesisItemOpen Access
    Impact of fertigation and drip system layout on performance of chilli(Capsicum annum)
    (Department of Land and Water Resources and Conservation Engineering, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 2012) Nadiya, Nesthad; KAU; Kurien, E K
    The study “Impact of fertigation and drip system layout on performance of Chilli (Capsicum annum)” was taken up with the objective of determining the effect of fertigation, drip system layout and different levels of irrigation for chilli under plastic mulch. Different fertigation equipments like ventury injector, dosmatic fertigation unit and fertilizer tank were tested to study the hydraulic performance of the system. Ventury injector for fertilizer application was found to have high suction rate in comparison with dosmatic fertigation unit. The suction rate and motive flow rate was found to vary directly with respect to the pressure drop between the inlet and outlet of the fertigation equipment. Ventury injector can be used only if the discharge rate is above 14.6 L/min. Dosmatic fertigatrion unit and fertilizer tank can be used if the discharge rate is above 1.1 L/min and 6.6 L/min. The moisture distribution pattern under different drip field layout was observed. The moisture content near to the plant base was found to be high and decreases as the distance from the emitters increased. The effect of different irrigation levels and drip system layout under plastic mulch on the performance of Chilli (Capsicum annum), Ujwala variety was also studied. The number of branches, stem girth and yield showed significant difference between the treatments. The yield showed significant difference with different levels of irrigation and drip system layout. Maximum yield of 18.32 t/ha was observed for the treatment T5. The treatments T6 (17.952 t/ha) was on par with the treatment T5. The benefit cost ratio for treatment T5, 85 per cent of the irrigation requirement with one lateral for each row of crop was 3.8 and treatment T6, 85 per cent of the irrigation requirement with one lateral in between two rows of crop was 3.9. Even though the yield for the treatment T5 was high, the benefit cost ratio stands high for treatment T6. The high value of benefit cost ratio for treatment T6 was due to the reduction in the quantity of material for drip irrigation system