Thumbnail Image

Theses

Browse

1982 - 198941990 - 19998
Reset filters
Subject: Agricultural Engineering × Author: KAU × End date: 1999 × Start date: 1980 × Thesis Type: M.Tech. ×
Reset filters

Search Results

Now showing 1 - 9 of 12
  • Thumbnail Image
    ThesisItemOpen Access
    Water balance study of Karuvannur river basin
    (Department of Irrigation and Drainage Engineering, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1988) Santosh, G Thampi; KAU; John Thomas, K
    This study was undertaken to quantitavely assess the water resources of the Karuvannur River Basin and to study the monthly water balance in order to estimate the balance for ground waterrecharge or depletion during the period 1976 to 1985. The mean monthly rainfall over the basin during the period 1976-1985 was determined by Thiessen polygon method . Data regarding the amount of water released for irrigation from the Peechi reservoir was also collected. Due to lack of data, contribution from other sources was not taken into account. The total runoff from the basin during each month of this period was determined . The various crop combinations in the basin were identified and the area under each of these was estimated . The actual evapotranspiration during each month was estimated using the method outlined by Doorenbos and Kassam. The basin was regarded as an independent hydrologic unit . Hence surface and subsurface inflow and outflow were assumed to be negligible.
  • Thumbnail Image
    ThesisItemOpen Access
    Development of a low cost garden tractor
    (Department of Agricultural Engineering, College of Horticulture, Vellanikkara, 1982) Sivaswami, M; KAU; Muhammad, C P
    The study was conducted with the objectives of systematic analysis of components with respect to their kinematics, dynamics and ergonomics and evaluation of traction performance and economics of low cost garden tractor. A greaves Lombardini 5.4 hp diesel engine with 1800 rpm was selected and a simple three step speed reduction system having a single stage V belt drive and double stage chain drives with a pivotted countershaft clutch have been designed. A road speed of 6.635 kmph and field speed of 3.317 kpmh were achieved by using a cone pulley arrangement with 6.00 x 12 size wheel.Correct position of various components bringe the centre of gravity of the unit with and without implement at very close to the final drive axle for easy balancing
  • Thumbnail Image
    ThesisItemOpen Access
    Development of small scale equipment for extraction of cocoa butter and production of cocoa powder
    (Department of Agricultural Engineering, College of Horticulture, Vellanikkara, 1982) Ganeshan, V; KAU; George, T P
    The primary objective of this project was to evolve a viable technology and equipment system for small scale processing of cocoa beans. The study mainly concentrated on the development of an extraction unit for the separation of butter from cocoa mass. Various equipment required for small scale processing of cocoa beans were either identified or designed.
  • Thumbnail Image
    ThesisItemOpen Access
    Development and field evaluation of a cardomom polishing machine
    (Department of Farm Power Machinery and Energy, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1999) Anu, Ray Mathew; KAU; Mohammad, C P
    Cardamom capsules when dried have a dried flower stalk which is hard to be removed by manual operation. For destalkinq, a power operated cardamom polishing machine was developed, tested and its performance was evaluated. A polishing drum with attached wooden blades seperated the dried capsules fed in. from the flower stalk attached and were collected seperately. A single phase 1 hp motor served as power source. A 3-factlJr, factorial experiment in Completely Randomized Design (CRD) with drum speed, feed/batch, and retention time as independent variables was performed.
  • Thumbnail Image
    ThesisItemOpen Access
    Design, fabrication and testing of a power operated paddy dibbler
    (Department of Farm Power Machinery and Energy, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1996) Jayarajan, R; KAU; Jippu, Jacob
    A 2-row power operated paddy dibbler was designed, fabricated and tested at Kelapaji College of Agricultural Engineering and Technology, Thavanur. The main components of the dibbler were two seed boxes, plungers reciprocating within the seed tubes, fluted roller seed metering mechanism, dibbler wheels, stationary cam, frame and transport wheels. The seed tubes were fixed radially around the dibbler wheel with 45 mm of it projecting outwards for penetrating the soil. The plunger was actuated by a stationary cam and during its upward stroke it uncovered the farther end of the seed transfer tube and transferred the seeds into the seed tube and then into the holes made in the soil. In the downward stroke the plunger closed the seed transfer tube. Simultaneously the fluted roller transferred the seeds in to the seed transfer tube. The average speed of operation of the dibbler was 1.32 kmph and its field capacity and field efficiency were 0.031 ha/h and 78.18 per cent respectively. The average number of seeds dropped per hill was 5 and the seed rate obtained was 78 kg/ha. The seeds were placed within the confines of the holes made by the seed tube and plunger. There was absolutely no scattering. The depth of placement varied from 3.8 to 4.6 cm. The operating cost of the dibbler was Rs. 502.58/ha. This mechanism offers scope for developing dibblers with more number of rows for being operated more economically.
  • Thumbnail Image
    ThesisItemOpen Access
    Modification and performance evaluation of six row rice transplanter for conventional seedlings
    (Department of Farm Power Machinery and Energy, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1990) Bainu, T Kuzhively; KAU; Sivaswami, M
    The work was carried out at the Kelappaji College of Agricultural Engineering and Technology, Tavanur. The six – row rice transplanter was originally designed for mat type seedlings. Considering the importance of a transplanter using conventional type seedlings, the above transplanter was modified. The modifications were completed in three stages. The performance evaluation of the modified six row rice transplanter was conducted after each stage of modification. The average number of seedlings per hill could be reduced from the average value of six seedlings per hill before modification to 2.27 seedlings per hill after the modifications. The missing hills percentage was brought down from 20.83 per cent to 5.55 per cent and the floating hills percentage was reduced from 10 to 5.55. Percentage of damaged hills was reduced from 23.3 to 8.8. The field capacity of the machine was improved from 0.0139 ha/hr to 0.0162 ha/hr and field efficiency from 48.26 percent to 56.87 per cent. The use of the modified transplanter is profitable if it is operated beyond one hectare per annum. It gives a saving of Rs. 618.00 per hectare compared to the conventional hand transplanting giving a 2. 4 times reduction in total cost. The pay back period of the modified transplanter is 2.24 years when the annual utilization is 2 hectares per annum and 1.13 years when the annual utilization is 3 hectares per annum.
  • Thumbnail Image
    ThesisItemOpen Access
    Erodibility and runoff potential of laterite soils under simulated rainfall conditions
    (Department of Irrigation and Drainage Engineering, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1999) Sajeena, S; KAU; Kurien, E K
    Soil erosion is one of the most serious environment degradation problems. However reliable measurement of erosion remains limited and estimates of soil productivity are even rarer. Assessing the extent and seriousness of erosion therefore remains a difficult task Nevertheless, identification and assessment of erosion problems could have an important role in influencing better land use and conservation practices. Rainfall simulators are considered as an effective tool in soil conservation research. Simulators make it possible to produce predetermined storms at any desired time and location. They make the replication of research easier and facilitate the study of storm sequences. Laterite soils are by far the most important soil group occurring in Kerala and cover the largest area. The objective of this study was to estimate the erodibility and runoff potential of laterite soils of three well defined series under simulated rainfall conditions. The rainfall simulator designed and fabricated by Kurien and George (1998) was modified for better performance. The modified simulator could produce rainfall intensities varying from 741 to 23.00 cmlh. Also uniformity of the rainfall produced could be increased to higher values of 88.10 and 91.53 per cent, thus giving a better performance. Intensity of rainfall increased as the 11 pressure of supply water to the simulator increased and a relationship was established between intensity and the supply pressure of water as 1= -87.205 p2 + 108.61 P - 10.786 (R = 0.99) Experiments were also conducted to study soil loss and runoff from three different series of laterite soils, i.e.Mannamkulam series, Naduvattom series and Vellanikkara series. The soil loss and runoff increased with increase in the rainfall intensity for all slopes studied for each series of soil. A general trend of increase In soil loss and runoff with increase in the slope was observed for all the three series of soils. Empirical equations were developed for estimating soil loss (E) and runoff (0) for various intensities of rainfall and land slopes for the three series of soils selected for the study. The equations are: Mannamkulam series E = 1167.797 I + 835.109 S - 21686.07 (R = 0.90) Q = 65.0161 + 16.747 S - 235.923 (R = 0.99) Naduvattom series E = 324.766 I + 112.799 S - 3912.219 (R = 0.97) Q = 74.542 1+19.434 S - 394.323 (R = 0.99) Vellanikkara series E = 115.662 I + 431. 064 S - 11512.284 (R = 0.98) Q = 58.742 I + 26.837 S - 310.019 (R = 0.99) ii1
  • Thumbnail Image
    ThesisItemOpen Access
    Performance evaluation of high discharge low head pumps
    (Department of Irrigation and Drainage Engineering, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1998) Rini Rani, S; KAU; John Thomas, K
    Paddy cultivation in Kuttanad and Kole lands is made possible only after large scale dewatering operations. These water logged lands have to be drained in the shortest possible time to initiate seed bed preparation. The short time available for seed bed preparation need adoption of high discharge low head pumps. The most commonly used centrifugal pump is incapable of giving corresponding increase in discharge rate even if the lift required is reduced to a minimum. So this study was undertaken to help to identify a suitable portable pump for meeting the specific requirement of drainage in Kerala. Mixed flow and axial flow pumps imported from Thailand were used for this purpose. The study included testing of lS-cm mixed and axial flow pump at the specially designed and constructed test bed at different speeds and at different water levels in the pumping sump. For each test, from the data obtained discharge, input power and efficiency were calculated. Using the calculated values performance characteristic curves were plotted and regression equations were developed for discharge efficiency, discharge - total head and discharge - input power relationship at each speed. Performance curves were also plotted keeping total static head const ant and regression equations of speed - discharge, speed - total head, speed - input power and speed efficiency relationships were developed. The maximum efficiency of IS-cm mixed flow pump was 42.16 per cent at a speed of 1000 rev/min, against a total head of 217.33 cm and a discharge rate of 49.47 L/s. The input power corresponding to this efficiency was 3.4 hp. The best performance of mixed flow pump was noted at a working speed of 1000 rev/min. The maximum efficiency of IS-cm axial flow pump tested was only 18.05 per cent at a total head of 160.55 cm and a discharge of 24.88 L/s. The corresponding speed was 2500 rev/min and input power was 2.95 hp. The best performance of axial flow pump was noted at a working speed of 2500 rev/min.
  • Thumbnail Image
    ThesisItemOpen Access
    Synthetic generation of streamflow data using computer simulation model
    (Department of Land and Water Resources and Conservation Engineering, Kelappaji College of Agricultural Engineering and Technology, Tavanur, 1993) Leven , K V; KAU; Jobi V, Paul
    A Study has been made to develop a computer simulation model for the synthetic generation of streamflow data for Chaliyar, one of the larger basins of the state. The data were collected from different river gauging stations for different durations. A suitable mathematical model namely Thomas Fiering Model was developed for the generation of synthetic data. The model was fitted for the observed monthly steamflows. The validity of the model was checked by comparing the statistical parameters of historical and generated data and by comparing the flow duration curves. It is seen that the model preserves various statistical parameters like mean, standard deviation and correlation coefficient. The study reveals that the computer simulation model developed is a very effective tool in the proper management of water resources system.